超声波清洗机除油的操作要注意什么？

1. Place greasy hardware, aluminum blocks, metals, bearings, chains, molds, etc. into a cleaning basket and then into a cleaning tank

2、加水并倒入一定量的脱脂剂

2. Add water and pour in a certain amount of degreaser

3、按下开关，超声波清洗机开始工作，清洗一段时间后，再放入另一个干燥槽干燥，干燥一段时间后，取出物体，清洗篮。

3. Press the switch, the Ultrasonic cleaning starts to work. After cleaning for a period of time, put it into another drying tank for drying. After drying for a period of time, take out the object and clean the basket.

4、停机，注意维护

4. Shutdown, pay attention to maintenance

使用超声波清洗机可以缩短除油除锈时间，提高除油除锈质量，强化除油除锈工艺。特别适用于零件和复杂硬件零件。表面难以除油和油脂的金属、轴承、链条和模具具有明显的除油和除锈效果，克服了人工清洗对零件造成的损坏。超声波除油基于空化原理，超声波频率40KHz为高频超声波。在超声波作用下，加上除油剂的化学作用，产生气泡的瞬间，由于受到压力的作用，气泡压缩破碎而分散，同时产生冲击波，这种冲击波可以清洗五金零件表面，使污垢脱落。

The use of Ultrasonic cleaning can shorten the time of oil and rust removal, improve the quality of oil and rust removal, and strengthen the oil and rust removal process. Especially suitable for parts and complex hardware parts. Metals, bearings, chains, and molds that are difficult to remove oil and grease on the surface have obvious oil and rust removal effects, overcoming the damage caused by manual cleaning to parts. Ultrasonic oil removal is based on the principle of cavitation, and the ultrasonic frequency of 40KHz is high-frequency ultrasonic. Under the action of ultrasonic waves and the chemical action of degreasing agents, bubbles are generated at the moment. Due to the pressure, the bubbles are compressed and dispersed, and at the same time, shock waves are generated. This shock wave can clean the surface of hardware parts and cause dirt to fall off.

超声波清洗机的除油除锈效果如何？事实上，除油除锈的效果与零件的尺寸、形状复杂度、零件的位置、表面的油成分、是否添加脱脂剂密切相关。正常情况下，超声波清洗机油和除锈频率为40KHz。零件的放置非常重要。零件在清洗槽中转动或旋转，使表面的每个部分都能受到超声波辐射的影响，从而达到更好的清洗效果。

How effective is the Ultrasonic cleaning in removing oil and rust? In fact, the effectiveness of oil and rust removal is closely related to the size, shape complexity, position of the parts, oil composition on the surface, and whether degreasing agents are added. Under normal conditions, the frequency of ultrasonic oil cleaning and rust removal is 40KHz. The placement of parts is very important. The parts rotate or rotate in the cleaning tank, allowing each part of the surface to be affected by ultrasonic radiation, thereby achieving better cleaning results.

超声波清洗机与超声波清洗剂一样，洗衣机与洗衣粉一起使用，清洗效果大大提高，

The Ultrasonic cleaning is the same as the ultrasonic cleaning agent. The washing machine and washing powder are used together to greatly improve the cleaning effect,

本文由通过式喷淋清洗机友情奉献.更多有关的知识请点击:   真诚的态度.为您提供为全面的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

This article is dedicated to the friendship of the through type spray cleaning machine. For more relevant knowledge, please click on: Sincere attitude. We will provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Stay tuned